Audiovox ACC 30 User Manual

ACC-30  
DIGITAL AUDIO 6 DISC  
COMPACT DISC CHANGER  
MODEL ACC-30  
6-DISC CD CHANGER  
INSTALLATION MANUAL  
BEFORE INSTALLING THE UNIT  
Transport Lock Screws  
The mechanism in the CD changer is "locked" into place during shipment by the 4  
transport screws. Be sure to remove the screws prior to installation.  
Retainthesescrewsforfutureusewhentransportingtheunitforservice/maintenance.  
l Caution l  
After removing the transport lock screws, place the supplied seals over the screw  
holes. These seals are used to keep dust out of the unit, which could cause a  
malfunction.  
Installation and Wiring Precautions  
To prevent a short-circuit,  
l Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.  
l Connect power wires last.  
1
Note  
If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect  
the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra  
caution during installation, not to cause a short circuit.  
Do not install the unit in the following locations.  
l Locations exposed to direct sunlight.  
l Where hot air is discharged from the car heater.  
2
l In areas subject to extreme temperatures.  
Incorrect installation can cause the sound to "skip" when playing a disc.  
Mount the unit firmly in place, using the supplied brackets and screws.  
3
Be careful not to damage the car wiring.  
4
l Be sure to use the supplied screws.  
l Be careful not to snag any wires when tightening screws.  
l Do not use any of the screws that are part of the brake or steering system, to install the unit.  
5
l This unit cannot be installed on its side, end, or upside down. Installation in such positions will cause malfunctioning  
6
of the mechanism.  
2
INSTALLATION  
The unit can be installed horizontally, vertically or at a 45° angle. The position of the built-in anti-vibration springs (left and right side), must  
correspond to the mounting position chosen. If the springs are not set correctly for the type of installation chosen, the anti-vibration  
compensation will not be effective and vibration may cause the disc to skip.  
HORIZONTAL INSTALLATION  
Set the anti-vibration springs to  
position "H".  
VERTICAL INSTALLAITON  
Set the anti-vibration springs to  
position "V".  
45° ANGLE INSTALLATION  
Set the anti-vibration springs to  
position "45°".  
position "H"  
position "45°"  
position "V"  
H
45°  
V
45°  
PROCEDURE FOR HORIZONTAL INSTALLATION  
1
Attach a mounting bracket to each side of the unit, using the  
4 hex head bolts with washer base.  
H
45°  
V
Bracket  
NOTE: Make sure anti-vibration springs  
are set to position "H".  
Hex head bolt  
with washer base  
Bracket  
2
Determine the mounting location, and drill four mounting  
holes.  
NOTE: If mounting surface is carpeted, use caution  
when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet  
before drilling into sub-surface.  
Drill holes 1/8" (4mm) in diameter.  
Self-tapping Phillips head screw  
Never mount the unit near the fuel tank.  
3
Secure the unit in place, using four self-tapping Phillips  
head screws.  
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
Bracket  
Bracket  
3
PROCEDURE FOR VERTICAL INSTALLATION  
Note  
If the anti-vibration spring position has been changed and verified for vertical mounting (as shown on page 3), start with step 2.  
Set the anti-vibration springs to position "V".  
Attach a mounting bracket to each side of the unit, using  
the hex head bolts with washer base.  
1
2
position "V"  
Bracket  
Bracket  
Hex head bolt  
with washer base  
Determine the mounting location, and drill four mounting  
holes.  
Mount the unit in place, using four self-tapping Phillips head  
screws.  
4
3
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
NOTE: If mounting surface is carpeted, use caution  
when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet  
before drilling into sub-surface.  
Self-tapping  
Phillips head  
screw  
Never mount the unit near the fuel tank.  
Bracket  
Bracket  
Drill holes 1/8" (4mm) in diameter  
4
PROCEDURE FOR 45° ANGLE INSTALLATION  
Note  
If the anti-vibration spring position has been changed and verified for 45° angle mounting (as shown on page 3), start with step 2.  
Set the anti-vibration springs to position "45°".  
Attach a mounting bracket to each side of the unit, using  
the 4 hex head bolts with washer base.  
1
2
position "45°"  
Bracket  
Bracket  
Hex head bolt  
with washer base  
45°  
Determine the mounting location, and drill four mounting  
holes.  
Mount the unit in place, using four self-tapping Phillips head  
screws.  
4
3
Use RTV (silicone sealer) on screw threads or around  
the holes to prevent moisture intrusion.  
NOTE: If mounting surface is carpeted, use caution  
when drilling holes to prevent drill bit from  
catching on carpet. Cut holes in carpet  
before drilling into sub-surface.  
Self-tapping Phillips head screw  
Never mount the unit near the fuel tank.  
Bracket  
Bracket  
Drill holes 1/8" (4mm) in diameter  
5
WIRING  
Mating 8-pin DIN socket on rear of  
compatible radio chassis (see Note below).  
Car Stereo with  
CD Changer Controls  
CD changer  
NOTE: 1. Check with your Rampage/Audiovox audio dealer  
to be sure your stereo is directly compatible with  
this CD changer.  
2. When used with Rampage model AV-427 car  
stereo, besureChangerSelectorswitchonbottom  
of radio chassis is set to position "B".  
6
© 1999 Audiovox Corporation, Happauge, N.Y. 11788  
Printed in Korea  
128-5572  

Asus Car Video System VH202 User Manual
Canon 2514A002 User Manual
Canon FS405 User Manual
Canon RE 450X User Manual
Clarion VZ309 User Manual
HP (Hewlett Packard) NC6400 User Manual
Hypertec TAE2702HY User Manual
JVC Camcorder GZ MG37U User Manual
JVC CS HX647X User Manual
JVC GET0701 001A User Manual